Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are durable, long-lasting and easy to maintain. They don't get rotten or rusty like timber and aluminum.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it can cause a great amount of damage to your home, which can make it very dangerous and uPVC repair potentially fatal. You should take the time to ensure that your windows are in good shape.

For single pane windows it is relatively easy to replace them, and the new window is usually able to fit into the frame that was previously installed easily. However If you have double-pane windows that are secured by internal beading, it'll be more difficult to get rid of the existing panes and install new ones. In this situation you'll need to locate some plastic spacers that will aid the new pane in being able to fit correctly into the window frame.

If you're planning attempt to remove the glass panes yourself it is crucial to wear the appropriate safety equipment such as gloves that are thick and eye protection. You should also lay down a dropcloth before you begin working on the window panes to ensure that any shards of glass fall onto the fabric, not onto the floor, where they could be trampled.

It's a good idea to seal the gap after the glass is removed. This will stop drafts and water from getting into your property until a professional arrives to repair the window. This will also provide an obstacle to stop criminals from getting into your home. If the distance between the window and the door is significant, you may prefer an alarm system that includes windows. This will give you the best of both.

2. Sagging

uPVC windows and doors are a low-cost, durable and energy-efficient alternative to timber windows with sash. However, over time, they may be afflicted by a variety of problems including sliding. A window that isn't properly aligned can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it's important to act quickly to stop the issue from becoming worse.

To repair a window that is sagging, you can try repositioning the hinges. To do this, you'll need to open the window so that you can get to the frame. Then, remove both the hinges at the top and bottom using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Once you've repositioned the hinges, close the window and check for an appropriate fit. If you're satisfied with the fit, you can tighten the screws to ensure that they stay in position.

If you are unable to move the hinges, you could have to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, causing them to loosen. If this happens, it's essential to replace the seal as soon as possible to ensure your uPVC windows are watertight and draught-proof.

UPVC handles can also loosen. Often this is due to screws that have become loose over time. However, it can occur because the handle mechanism has been worn out. It's relatively easy to fix a loose uPVC hand. First, you'll need to shut the window and then perform an initial fitting. The corner joints of the sash must align with the casing joint. If it doesn't then you can use the screwdriver to loosen the handle. Then, you can turn the mechanism into position.

3. Water Leaks

It is essential to act if you get up each morning to find mouldy walls and wet floors. The leaks of water through windows could cause structural damage to your home, and affect your ability to regulate the temperature inside your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a fairly simple fix that can be done by any DIY expert. Depending on the severity of the issue is, old caulking may have to be removed. When it is time to uPVC repair, you must avoid 'over-caulking'. This will only make your window harder to clean and decrease its energy efficiency.

Verify that the drainage holes have no debris inside them and that the sill pan has been angled correctly to drain away from the window doctor. In more severe instances, you may need to replace the window.

Mold spots and rotten sills are also signs of water leakage. The fungus thrives in damp conditions and can quickly spread across the home.

If the leakage occurs between the double-glazed glass, it is more likely the problem is with the seal than the frame. A uPVC specialist can fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame if your uPVC window is difficult to open, or if it blows open with an ease. Any competent DIYer can replace hinges in just a few minutes.

Like all mechanical parts hinges are prone to be damaged over time. It's easy to change the hinges on a window replacement near me however it is easier if someone else helps you to hold the frame.

Verify that the uPVC hinges are closed and open in the correct direction. You can check this by looking for the arrow on each hinge. This shows which way the window should open.

The issue could be caused by opening the window incorrectly or by a poor installation at the factory. It is usually possible to fix the issue by sending us a photograph through our website and we will be happy to give you suggestions.

It is also important to lubricate the hinges regularly. This can be done by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication will make the window easier to open and close. It can also stop corrosion and reduce the possibility of sticking. This should be done at least every year. WD40 or other solvent-based oils should not be used since they can damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges may also become unbalanced due to wear, causing an opening where the sash and frame meet. They can be fixed by giving them a good clean, but if they are beyond repair it might be necessary to have them re-aligned or replaced. The interlock, which is on the hinge side of the window and can be misaligned. Again, it is possible to give them a good clean, but in some instances it could be necessary to have them replaced.

The next common cause of draughts is the window seals, these are susceptible to being worn out or damaged over time and will allow air to escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Another alternative is to replace the upvc window with glass that is low-emissivity, this will help to regulate indoor temperatures and will reduce the risk of draughts.

The last way to reduce the amount of draughts is to use a Draught-excluder. These are usually fabric tubes filled with a filler which can be placed over your window sill. These will help to stop cold air from entering and keep your home warm and cozy!

The windows made of upvc can remain a great source of insulation and security for your home with a little regular maintenance and repairs. It is essential to remember that all windows eventually get worn out and it could be more cost-effective to replace them instead of fixing them. If you are experiencing issues with your Upvc windows, it is always recommended to seek assistance from a professional as soon as possible.