UPVC Replacement Door Handles

The handles on your doors get worn out with time and require to be replaced. It is essential to be able to match the dimensions of the replace window handles that were previously used when replacing them.

The top screw's position as well as the lever and keyhole sizes are the three measurements you have to check. Refer to the size guide for assistance in this.

Inline Lever/Lever

A lever door handle is a modern handle that can be put in on doors that are new or replacement double glazing window handles. This style of handle is available in various designs and finishes. A number of manufacturers make this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The upvc replacement door handles/Composite handles are made from robust materials, and are perfect for multi-point lock doors that require a robust design. The handles are inline, and use the same spindle and screws to fix them. They are easily fitted on any uPVC/Composite doors.

The design of the sprung lever allows the handle to be set and angled for comfortable operation and is suitable for all users. The handle has been endurance tested to 200,000 cycles, which allows for the assurance of the quality of the finish and the performance of the handle over time. The lever that is sprung can be cut to fit the widest range of locks. This is particularly useful for doors with narrower openings where the cylinder is situated further back from the door. A lever that is shorter is an excellent option for doors where the latch can be activated by the thumb turn on the inside.

Lever Pad

The lever pad upvc handle is distinct from the lever handles commonly found on doors. These handles can work off one single spindle (inline) or independently from both sides using two offset or inline spindles (pad). They are generally used on UPVC double glazing handles-glazed doors and are available in a variety of variations and finishes.

The handles have been tested to a minimum of 200 000 cycles and are available in various finishes, including White, Silver, Chrome & Gold. The finish is compliant with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high degree of durability and performance for the intended use.

All of the UPVC lever pad designs are supplied with the spindle and screws which allow them to be put on a new or existing uPVC door. The backplate fixation centres of 211mm allow for a wider handle, which is typically a benefit when replacing an old or faulty multi-point door lock mechanism. These handle levers are also spring-loaded, which solves the issue of handles hanging out of the horizontal position when they are not in use.

It is crucial to ensure that the PZ dimensions for both the multipoint lock and the uPVC doors when choosing the replacement UPVC spindle and handle. This measurement is also called 'handle centres' or cylinder centres'. It is important to match the correct handles.

Once you have the proper PZ size you will then be required to make sure that the lever pads and push pads are of a suitable shape to fit the American with Disabilities Act (ADA) approved handles you require for your doors. They are usually rectangular or round in shape, with an internal lever and external push pad.

The majority of UPVC lever pads that we offer are sprung, which means that they return to their horizontal position after not being used, instead of hanging out and possibly securing in the frame. This stops draughts and cold air from getting into a house. You will also find that the majority of UPVC lever pad handles are hand-operated which allows you to place them on either side of the door.

Euro Cylinder

Cylinder locks are found on uPVC and replacement door handles other kinds of doors. They operate by using a key that unlock a cylinder case that will reveal pins that can be aligned to those inside the lock body, permitting them to turn an revolving cam, opening the door. Euro cylinders can be fitted with up to six pins, with internal and external doors typically requiring different levels of security.

The selection of a cylinder is essential. It is based on the type of use your doors and handles will receive. External doors, for example, should be fitted with higher security cylinders while internal doors can be secured using a standard cylinder. Some cylinders have extra features that can improve security, like anti drill or anti bump properties.

To make sure that the euro cylinder is of the right size for your door, it must be measured correctly. The cylinder should be measured from the hole for fixing screws in the middle to each end of the cylinder and the thumb turn if you have one. If you are unable measure it with the lock in position, Replacement door handles you can remove it. It is essential to not have a cylinder that extends beyond the handle or escutcheon. This can make it susceptible to lock snapping attacks.

The design of the latest cylinders comes with anti-drilling as well as bump resistance features. These features are designed to minimize the chances of an attack by forcing the cylinder to rotate in a different direction. This will help deflect the attack, and ensure your door is secure.

Some cylinders are designed to resist snapping. This is an increasingly common method of attack on cylinders where the break line in the lock is targeted with a special tool to snap off the front of the cylinder to allow the door to open. This is a quicker and easier way to gain access than using a multipoint locking system. It also leaves less evidence of the break-in which can delay insurance claims.

Spring Cassette

The spring cassette is positioned in the base of the door handle backplate, supplying a spring-loaded solution that returns your multipoint lock handles to their normal position after using. The handles had no spring, and would slide when the locking mechanism was disconnected. This component is the best way to address this issue. It also stops your upvc door from becoming stuck in either the closed or open position since they aren't easy to close manually.

These spring cassettes have been specifically designed for use with sprung multipoint locks They will not work with multipoint handles that are not sprung and you will require a bespoke hole cut into the backplate to allow them to fit (please see image for technical diagram). They are a replacement for broken or missing cassettes within the backplates of door handles of many brands of uPVC doors. They are fitted with a square cut-out that accommodates an 8mm spindle and they are supplied individually.

These spring cassettes are a fantastic value-for-money way to fix the problem of handles on your doors sagging. They are easy to fit and will prolong the life span of your uPVC doors. Contact us to learn more about our range of uPVC accessories and spares. We are always ready to provide professional advice and assistance you.