Reasons Your fiat panda key replacement 500 Key Fob Won't Work

A key fob for fiat key duplication 500 makes it easy to open doors and start your car. There are many reasons the fob won't work. These include a dead coin battery, water damage, receiver module issues, and interfering.

This listing is for an NEW replacement key for fiat 500 fiat 500 key cover uk Flip Key Remote that appears similar to the Ilco brand. It must be professionally programmed (click here to search for local automotive locksmiths). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob doesn't function is due to the battery is dead. Modern key fobs come with a limited operating range, and should be within some feet of the vehicle to operate. If you're far from your vehicle, and you push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a new one of a reliable brand, such as Panasonic Duracell or Energizer. You can find them in the local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while standing close to your fiat Key duplication 500. The parking lights will flash and the key fob should operate the lock and unlock switch.

If the key fob doesn't work after replacing the battery, it might be damaged by water that blocks it from communicating with the receiver module inside your car. Water damage can occur in a number of ways, from a light splash to submerging your fob in salt water at the beach. If you suspect that your fob has been exposed to water, you can place it in a bag of rice to draw out the moisture. If this fails, you'll have to get your fob reprogrammed either by an auto locksmith or a dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean, or wash it in a washing machine. Saltwater can cause the circuit board to short and eventually die. The fob getting wet is not an ideal idea however, if you drop it in a glass of water or forget to remove it from your pants pocket prior to running the washing machine do not give up hope.

Remove the battery first. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Check the fob to check if it's working. If the key still doesn't work, it may have to be reprogrammed. This is typically done by a dealer or professional auto locksmith.

If the key you have is older and not programmed for your car it is necessary to replace it completely. A professional locksmith for automotive can carry out this simple task. The locksmith will have to cut the key to match the ignition of your vehicle. The locksmith also needs to reprogram the fob into the vehicle's system. This is a cheap and quick procedure that can be completed in the same day.

Receiver Module Issues

The 500 key fob could not work because it's out of range. The remote usually has an area of 30 feet or less and if it's far from your vehicle, it will not respond to your commands. You can solve this issue by moving the remote closer to your vehicle until it responds.

If your fob does not work after replacing the battery for the coin, also known as a "button", "watch" or "button" It could be due to a problem with the internal circuit board. Reprogramming the fob usually resolves this problem. You can find the procedure for most vehicles on YouTube or in the owner's guide.

It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they loose tension, it could prevent your coin battery from being properly seated and cause your remote to malfunction.

In rare instances, the fob can become out of sync with your vehicle because of hardware or software problems. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases the software might require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit an signal. This can happen when the key fob is close to a radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob might not function include a poor connection to the buttons, damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. battery replacement, reprogramming and using the spare key fob, you may have a defective receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

There is a simple way to reset the 500's internal system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then reconnect the battery. This will get rid of any residual electricity and restart the lost car keys fiat's computers, which could help the key fob to function again. If the problem persists you should seek out an expert technician. They'll be able diagnose the exact cause of your issues.