fiat punto key fob replacement 500 Replacement Key Fob

If your 500 remote key fob isn't working, it might be time to replace the battery. However, if you replace the battery but it continues to stop working it may be elsewhere.

United Locksmith specializes in the creation of new keys for classic vehicles. We have the tools and parts needed for this job.

Dead Coin Battery

The most frequent reason why your Fiat 500 key fob will not unlock or lock the doors is due to a dead battery. The battery inside the key fob can be depleted quickly if you don't use it often enough. If your remote starts to show signs like a loss in range or stopped functioning or not responding, then the battery could be dead.

The battery inside the key fob is held in place by metal clips for retaining. If the clips aren't tight enough, it can cause problems with contact, which can prevent your remote from receiving power. With a small flathead screwdriver, break the retaining clip outwards to remove the battery and replace it with a new one. Make sure to use a battery with the same voltage, size, and specification as the original.

Water exposure can cause the key fob to corrode, or even become damaged. Even a small bath in warm, soapy water could cause damage to the chip. It is best to keep your key fob in a dry location.

Water Damage

Water damage may be the reason behind your key fob not functioning properly. The rubber seals on key fobs keep them from getting damaged by a slight drizzle or splash of water. However, it is crucial to keep the keys from the washing machine, the ocean and even the pool.

The key fob is equipped with an electronic chip inside it that sends a signal to your car's immobilizer system. The chip allows the 500 to lock and start. If it gets wet, however it won't work.

You can clean the internal electronics of your key fob with isopropyl alcohol or an electronic cleaner to see if they are still good. However, it's recommended to purchase a replacement from a dealership rather than trying to fix the key fob that is submerged in salt water.

A replacement fob may cost you a few dollars however, it's cheaper than having to have your Fiat 500 towed to a dealer and fixed there! You can also do it yourself with some simple steps. Just ensure you have the correct battery type before you attempt to open your key fob. You can find step-bystep directions for every car keyfob online.

Faulty Chip

The chip inside the key fob is in direct communication with the immobiliser in your car to ensure that your vehicle will only start when the proper keys are inserted. If the chip is damaged, or corrupted, your car won't start no matter what you do.

Damage to the water or a dead cell phone battery are among the most frequently cited reasons for defective chips. Regardless of the reason, it is an ideal idea to hand this task to a locksmith since they will be able to replace the chip quickly and at a cost-effective price.

If your key fob does not function after exposure to clean rain or tap water take it off the battery. Clean the electronic component with an old towel. If the key fob still isn't working it's most likely an issue with the chip and will need to be replaced.

Many people will seek out their dealer when in need of a new fiat Car keys Cut key fob, however this is a expensive alternative. United Locksmith is the best choice if you are looking to have your Fiat keyfob repaired at a reasonable price. We have the tools and expertise required to repair your Fiat key fob in a timely and professional manner.

Faulty Receiver Module

Fiat key fobs send an alert up to 50 feet to the vehicle, which can unlock and lock the doors (and start the vehicle if it has automatic transmissions). There are several reasons why the fob might stop working. This includes a dead coin battery, water damage or Fiat Car Keys Cut worn buttons, a receiver module issue and signal interference, or an electronic chip that is malfunctioning.

If the fob has been stored in a place that has been subject to extreme trauma, such as being dropped on hard floors or getting washed in a washer and it isn't able to communicate with the car's Body Control Module (BCM). This is because the BCM is a secure system that can only accept signals from a genuine original key, and not from any other.

You will need to replace the fob if this occurs. A professional locksmith can handle all aspects of the key replacement process and even program a new one for the 500. They can even provide an identical fob that functions just like the original (and costs less than what it would cost).